moonbars.blogg.se - Mapsource for mac download

#Mapsource for mac download how to
#Mapsource for mac download install
#Mapsource for mac download update
#Mapsource for mac download Pc
#Mapsource for mac download series

MapInstall will combine all the maps into one gmapsupp.img file to send to your GPS.

When you are finished, select the Send Maps button. If you want to add maps from another map set, just select the other map set from the pull down menu and add them as above. At the bottom of the window shows how much memory you have available and also what you have used.

You can click on tiles to select them or marquee a selection here I have selected the complete map.

In this example, we have chosen Arizona Topo:

In the upper left of the window you should see a pull down menu where you select the map set you want.

If you see a screen like the one below you might want to check that you have the correct data card in the reader before you wipe out anything you might need later:.

Select your GPS or card reader and click Continue.

MapInstall will not make it past the second page unless you do this or if you are installing to a card reader, you will want it plugged in and the card mounted.

First off, plug your GPS into your Macintosh and have it turned on.

#Mapsource for mac download how to

Once you have the maps on the GPS you can follow this tutorial to show how to hide and show different maps.

You will get a success message at the end similar to: “The data has been successfully sent”.

MapInstall will now build the map sets and send them to the GPS unit or memory card depending on which you selected.

The next screen will tell you what maps are going to be loaded.

Select the segments you want from each map and then click Continue.

You can now switch maps at the bottom.

Note: Older GPS units have a 2025 map/segment limit and will only read 2gb of card data so be sure to watch that.

#Mapsource for mac download update

This will update the amount of space bar left at the bottom. To unselect segments click and drag with the right mouse button. Selected segments will outline in yellow while being selected and be outlined in black with a blueish tint when selected.

To select the parts just click and drag across the map.

At the bottom of the new window you can select each map that you want to load pieces of.

If you have unrecognized maps on your GPS (maps you have previously installed that aren't installed on this computer you can delete them at this point to save space.

This is the starting point for older GPS units. The steps below will go through the advanced/partial install.

#Mapsource for mac download install

Optional for newer units, required for older units: If you have limited memory space to just want to install specific parts of the maps click the Advanced/Partial Install button in the lower left corner.(Note: This option will also not exist with older units such as the 60CSx) You can select and unselect as you see fit and it will install the entire map selected.

The next screen will show you all the maps installed on the unit currently.(Note: This option will not exist with older GPS units that only allow one compiled map per device (60CSx and similar) All my maps will not fit and thus I have to select the maps I want to use. If all of your maps will fit on your GPS it gives you a quick option to install them all. Right click on either the card or device and select "Install Maps".The device/card should appear on the left side as shown:.Plug in the device you would like to load the maps to (a microSD card, SD card, or the actual GPS unit)įor this tutorial I will be using a Garmin Dakota 20 and also a Garmin 60CSx with memory card installed in the GPS using a card reader will allow for faster map installs.Note: You'll need version 2.0.9 or higher to load custom maps. Open Garmin BaseCamp (all screenshots from version 4.3.4).This also causes a variation in how you select maps this variation will be covered in this tutorial. For older units it will have to rebuild the entire map database you've selected each time. For newer GPS units (Garmin Colorado and newer including Dakota, Oregon, Montana, and 62 series) the program will allow you to manage maps very easily/quickly. When loading maps onto your GPS Garmin BaseCamp is the preferred program.

#Mapsource for mac download Pc

Loading The Maps With BaseCamp and MapInstall on a PC Warning: If you bought a micro-SD card that contains maps from Garmin DO NOT overwrite this card, use another card.

PC: Use BaseCamp/MapInstall To Load Maps.

This tutorial was updated in July of 2014 for the updated PC process. This how-to will detail how to load additional maps to your GPS unit with either a Mac or a PC. These receivers can still have maps loaded to them though in addition to the maps that already exist.

#Mapsource for mac download series

These days many of Garmin’s new GPS receivers contain built in maps, from the nuvi series with road maps to the Colorado and Oregon with topos. Author: Dan Blomberg & Rex Coggins | Last updated July 19th, 2014 at 11:37pm